Fence & gate company in Irving, TX

Fence and gate work in Irving starts with choosing the right structure for privacy, security and daily access. Repair may make sense when damage is isolated and posts remain sound. Replacement is worth considering when supports fail across several sections. For driveway gates, available clearance, gate weight and intended use guide the design.

Service area › Irving

What type of wood fence should I choose in Irving?

Start with the amount of privacy you want and the maintenance you are prepared to handle. Cedar and pressure-treated pine are materials to compare, but the boards alone do not determine how well a fence performs. Posts, horizontal rails, fasteners and drainage around the structure matter too.

A side-by-side layout places pickets next to each other. Small gaps can develop as boards dry. Board-on-board construction overlaps pickets, helping maintain screening as the wood moves. That overlap uses more material and adds weight, which should be reflected in the supporting frame.

Ask an estimate to identify:

• Wood species and whether lumber is treated.
• Picket layout and proposed fence height.
• Post material, spacing and installation method.
• Rail arrangement and exterior-rated fasteners.
• Walk-gate width, hinges and latch hardware.

Galvanized or stainless-steel fasteners should be selected for compatibility with the wood and exposure. Avoid comparing proposals that describe only “wood fence” without identifying the actual construction.

Should I repair or replace my fence?

Check the structure before deciding how many boards to replace. A leaning section may have a failed post, loose connections or soil movement at the footing. Replacing pickets will not correct a weak support.

| Broken or missing pickets | Damage is limited and rails are sound | Deterioration affects boards across the fence |Leaning sections | One post or connection has failed | Multiple posts are loose, rotted or displaced |Sagging walk gate | Hinges, latch alignment or bracing need attention | The frame and supporting posts are failing |Repeated repairs | Earlier damage had a clear, isolated cause | New failures keep appearing in adjacent sections

Repair is not automatically the lower-cost long-term choice. Ask whether the retained sections can support the repair and whether new wood will differ visibly from the existing boards. Replacement can resolve connected problems, but sound sections should not be dismissed without inspection.

Is a swing gate or sliding gate better for my driveway?

A swing gate needs an unobstructed arc as it opens. A sliding gate needs room beside the driveway for the leaf to retract. Neither configuration suits every entrance.

| Clear space inside the property | Needs room through the opening arc | Does not need a swing arc |Limited side clearance | May fit where a gate cannot slide sideways | Needs sufficient runback space |Rising driveway surface | The leaf may contact the slope | Track or cantilever design needs careful planning |Surface debris | Keep the swing path clear | Ground tracks need attention to debris

Measure both the clear opening and the space around it. Consider where vehicles stop while waiting, where pedestrians walk and whether an open gate would obstruct another access point. Gate width alone is not enough to choose the configuration.

What should an automatic gate and access-control system include?

An automatic gate is a complete moving system, not just a motor attached to a gate. The leaf should move freely, stay aligned and have sound supports before an operator is considered.

The proposed system should address:

• Operator suitability: Match the equipment to the gate’s dimensions, weight, configuration and expected use.
• Entrapment protection: Identify pinch and crush locations and select compatible monitored protection, such as photo eyes or sensing edges, as required by the system design.
• Access methods: Decide whether remotes, a keypad or another entry method fits daily use.
• Power and wiring: Establish the electrical supply, wiring route and equipment locations.
• Manual release: Explain how authorized users can operate the gate during a power interruption.
• Service access: Keep controls and mechanical components accessible for inspection and maintenance.

Do not assume a vehicle-detection loop provides pedestrian entrapment protection. Those functions are different. Ask for a clear explanation of each device, what it detects and how the gate responds.

How much does fence installation cost in Irving?

An accurate estimate depends on the measured scope and site conditions. Without those details, a single price can conceal differences in materials, removal work and structural requirements.

Fence length and height affect material quantities. Post selection, layout changes, difficult access and removal of existing concrete can also change the work involved. Gates add frames, supports and hardware; automation adds equipment, wiring and safety planning.

To compare estimates, look for the same scope in each:

• Measured fence length and proposed height.
• Material specifications and picket arrangement.
• Post, rail and footing details.
• Number and size of gates.
• Removal, hauling and disposal.
• Staining or other finishing, if included.
• Electrical and access-control work, if applicable.

Ask what is excluded as well as what is included. A lower total does not tell you much if one proposal retains old posts while another replaces them. Keep optional work separate so you can decide what belongs in the project now.

What information should I gather before requesting an estimate?

Gather enough information to explain the problem, not enough to design the whole job yourself. Morrison Gate & Fence can use a clear description and photos to understand the scope you want reviewed.

Useful starting information includes:

• The Irving property address and a way to reach you.
• Photos of the full fence line and close-ups of damage.
• Approximate length, desired height and gate locations.
• Whether you want privacy, easier access, repairs or a different layout.
• Known drainage issues, slopes or obstructions.
• Any available survey or previous layout documents.
• For automation, photos of the gate, hinges or rollers, operator and nearby power supply.

Identify any sections you want to retain. Also mention pets, pedestrian access and areas that must stay accessible during work. You can send your project details through the contact page and ask which measurements or documents would help with an estimate.

Does Morrison Gate & Fence serve cities outside Irving?

Morrison Gate & Fence serves the Dallas-Fort Worth metroplex. If you are comparing locations for another property, the Dallas service page and Garland service page cover nearby cities in Dallas County.

Use the service-area overview to explore coverage, and provide the actual project address when you inquire. Conditions at each property—not the city name alone—determine fence layout, gate clearance and the work needed.

Should I confirm my property line before replacing a fence?

Yes. An existing fence is not proof of the legal boundary. Review your survey and resolve uncertainty before setting new posts or changing the fence alignment. If the boundary remains unclear, consult a qualified surveyor. Also identify any easements that could affect the proposed location.

Can a wood fence be stained after repairs?

Yes, provided the retained wood and replacement boards are suitable for coating. Clean the surface, address decay and let the wood reach the moisture condition specified by the stain manufacturer. New and weathered boards may absorb stain differently, so a test area helps set realistic expectations for color.

Can an existing driveway gate be automated?

Sometimes. The gate must be structurally sound, properly supported and able to move freely without an operator forcing it. An assessment should check hinges or rollers, alignment, weight, clearance, power and entrapment hazards. Worn posts or a distorted frame may need correction before automation is appropriate.

Do I need approval before changing a fence in Irving?

Check with the City of Irving before changing fence height, location or configuration, and review any applicable private property restrictions. Requirements depend on the proposed work and property. Do not assume an existing fence establishes what is allowed now. Confirm who will handle any required applications before work begins.

Request an estimate for your Irving fence or gate project. Call Morrison Gate & Fence at (469) 654-7729 to discuss the condition, layout and options for your property.